Ask Me

What's the difference between the HaloTubephone and the "other guys"?

 

 

Soft malleable-wire headband

The soft headband wire can be easily bent or stretched into any shape to accomodate any lump or bump on the noggin.  If there is any pressure point, simply reshape the headband with a gentle pressure between the thumb and fore finger.

The headband wire on the "other guys" headset is made from a stiff spring steel, and cannot be easily re-shaped.  If theirs fits, then great...if not, well...

Speakers located away from the ear canal

Speaker location is very important to reliablity.  Sweat and earwax is produced naturally from the ear and migrates to the sensitive speaker components where they cause problems.  Speakers that are located in close proximity to the ear canal by only a foam ear tip are very prone to blockage.  Once blocked with vaporized sweat/cerumen, there is little the pilot can do except to send the headset back to the manufacturer for repair.

The speakers used on the HALO TubePhone are located at a considerable distance from the ear canal.  Sound is sent through the tubes to the ear.  Sweat and cerumen deposits are trapped in the tube before it can reach the sensitive micro speakers.  The pilot can see the sweat before it becomes a problem through the clear tubes, and they can be easily replaced by simply pulling them off and replacing them in the field or even in flight.

Replaceable sound tubes (no wires to fray or break)

Sound tubes do not contain wires as in the other guys headset.  No electrical signal needed to the ear, so wires won't break or fray from inserting them in and out of the ear canal.

(By the way, less sound enters the ear through the tubes than enters the ear via the foam ear tip.)


Independent volume controls

Separate volume controls for each ear. Good for those with unilateral hearing loss.  The competition uses a set-screw balance control. 

 

Gold-Plated audio plugs


Adjustable headband rod

The adustable headset rod can be extended to fit ANY size head.  Pull out for a larger fit, push in for a smaller head.  Re shape the heaband to fit the circumference of any head.


Do I need custom earmolds? 

NO...Custom earmolds are not recommended for the following reasons...

  1. They take time and effort to get
  2. A FULL 30% of all earmolds leak somewhat. The noise spectrum that enters the ear canal with small leaks are the low frequencies...engine noise.
  3. IF you get a good seal, that means it is pneumatic and cannot equalize pressure at various altitudes
  4. they cost range from $80 to $200 / pair making the experiment an expensive one.

Stick with the foams if at all possible.

Are they really as quiet as you claim?

Yes!  However the HALO Tubephone is an EARPLUG and not an EARBUD and must be inserted properly to have full noise quieting and fidelity.  There is a video showing the proper insertion technique on the SUPPORT pull-down menu at the top of this web page.

What is the difference between the regular and low gain mics?

The low gain mics are for ERJ/CRJ commuter aircraft ONLY!!!.  The gain has been dropped for intercoms that cannot be turned off (no squelch or mute) - otherwise known as "HOT" mic systems.  To keep the commercial co-pilots happy, the gain has been reduced.  If you are unsure what mic to order, PLEASE ORDER THE REGULAR microphone option!!! 

Will the low gain mic work on other non-ERJ/CRJ aircraft?...YES!  You will need to have the mic slightly closer to your lips, but yes...they will work just fine.

( Please note that while we provide this option to commercial pilots, the current version of the Halo is not TSO certified for 121 or 135 operations.  )

What aircraft does the HALO Tubephone NOT work with?

MD-80 and MD-88 INTERPHONE (crew and passenger PA) systems are incompatible with the HALO Tubephone (and many other headet microphones as well).  Use with the radio and intercom for communications are fine.